Engl Screamer 100 Manuel de l'opérateur télécharger pdf (Page 3)

Rear Panel

17 AC Socket: Connect AC cord here.

CAUTION: Ensure you use an intact AC cord with an insulated plug only!

Before you power the amp up, ensure the voltage value printed beside the

AC socket corresponds to the available current.

18 AC Fuse Box: Contains mains fuse (rear chamber) and spare fuse (front chamber).

NOTE: Ensure replacement fuses bear identical ratings (refer to the table)!

19 Footswitch V.L.S., Reverb: 1/4" stereo jack for double footswitches, executes the following

functions:

1.Switching between the two Master volume levels Hi and Lo (mono terminal)

2.Reverb on/off (stereo terminal).

20 Footswitch Clean / Lead, Lead Boost: 1/4" stereo jack for double footswitches, executes the

following functions:

1.Channel switching between Clean and Lead (mono terminal)

2.Lead Boost (stereo terminal).

All functions that can be accessed via footswitch can also be switched via the ENGL MIDI

Switcher Z-11. Simply connect the two 1/4" stereo jacks (19) and (20) to the stereo inputs

of the Switcher via two cables equipped with 1/4" stereo plugs. You can control switching

functions via the buttons on the Switcher. The respective settings of the functions (e, g. Lead

channel, Lead boosted, Reverb active, Hi Master volume) are saved to the desired MIDI program

locations. The ENGL MIDI Footswitch Z-12 is ideal for activating MIDI programs. When used in

conjunction with the ENGL MIDI Switcher Z-11, this durable footswitch does not require a separate

AC power pack. The requisite power is routed via the MIDI cable.

21 F.X. Loop Send: Signal output for the Effects loop. Connect this output to a signal processor’s

input/return jack via a shielded cable with 1/4" plugs.

22 F.X. Loop Return: Signal input for the Effects loop. Connect this input to a signal processor’s

output/send jack via a shielded cable with 1/4" plugs.

23 Balance: FX mix control for the Effects loop: Rotate the knob to the Dry position for the pure amp

signal, i.e. no effect on the signal. Turn clockwise to blend in an effect connected to the loop

to the dry signal (parallel/passive). At the Effect position, only the wet signal, i.e. the signal

sent from the FX device is fed to the power amp (serial/passive).

NOTE: If no effects processor is connected to this loop, leave this control in position Dry!

24 Poweramp Output, 4 Ohms parallel: 4 ohms speaker output jacks, internal connected parallel.

For diverse cabinet options see the last chapter on this page!

25 Poweramp Output 8 Ohms parallel: 8 ohms speaker output jacks, internal connected parallel;

the internal 8 ohms speaker is connected to one of this two jacks at the combo E340. For diverse

cabinet options see the last chapter on this page! The impedance of a additional cabinet for the combo

should bear 8 ohms.

26 Poweramp Output 16 Ohms: 16 ohms speaker output jack. For diverse cabinet options see the

last chapter on this page!

NOTE: Never operate the amplifier without a sufficient load, otherwise you may damage or destroy the

power amp! Ensure your cabinet’s specifications match the respective output’s specs.

Choose only one of the following cabinet options:

A: One 4 ohms cabinet connected to a 4 ohms jack; (Combo E340: without the internal speaker to

reach the maximum power !);

B: Two 8 ohms cabinets connected to the 4 ohms jacks; Combo: An external 8 ohms cabinet and the

internal 8 ohms speaker connected to the 4 ohms jacks. When you unplug the cable for the

external cabinet, ensure you plug the internal speaker back into the 8 ohms jack!

C: One 8 ohms cabinet connected to a 8 ohms jack (Combo: The internal speaker is connected to a

8 ohms jack);

D: Two 16 ohms cabinets connected to the 8 ohms jacks (Combo: without the internal speaker !);

E: One 16 ohms cabinet connected to the 16 ohms jack (Combo: without the internal speaker !).

21 22 23

17 18

Footswitch

F.X. Loop

Send Return Balance

Level

Line Out

Frequency

Compensated

Overload

Poweramp Output

Dry Effect

SERIAL NUMBER:

WIRED FOR:

REPLACE FUSE

ONLY WITH SAME

TYPE AND RATING !

V.L.S.

Reverb

8 ohms parallel

1 x 8 ohms

2 x 16 ohms

internal

speaker

16 ohms

Balanced Line Output

4 ohms parallel

1 x 4 ohms

2 x 8 ohms

MADE IN

GERMANY

All-tube Guitar

Combo Amplifier

Screamer

TYPE 340

Amp-Design by

Horst Langer

VOLTAGE FUSED

100-120 V

220-240 V

5 A

2,5 A

DO NOT OPEN !

RISK OF ELECTRIC SHOCK !

DO NOT EXPOSE THIS EQUIPMENT

TO RAIN OR MOISTURE !

CAUTION !

Clean / Lead

Lead Boost

230 VOLT

095660

25 26

1 2 3 4 5 6

Commentaires sur ces manuels

Pas de commentaire

Engl Screamer 100 Manuel de l'opérateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Amplificateurs audio Engl Screamer 100