Operator´s ManualPlease, first read this manual carefully!Tube Guitar AmplifierRAIDER 100
measures the current sent to the tube. If it is still too high, the power amp must bechecked by a service technician, and the tube may have to be repl
this volume control is located pre effects loop, it also determines the effects send levelfor Channel 2. The red LED to the right of the knob lights u
the power amp's volume to two different levels, and then access these volume presetsin combination with preamp voicing features such as . The min
Balance is set somewhere between dry and Effect). The FX Loop button enables andbypasses this loop, meaning you can actually activate and deactivate c
33 Mains Fuse Box:CAUTION: ALWAYS make sure replacement fuses are of the same type and have thesame ratings as the original fuse! Please refer to the
Note also: A footswitch may be equipped with LEDs indicating the given switchingstatus. Each of the two switches is provided with approx. 10 milliampe
gain rigs to generate undesirable peripheral noise in overdriven channels. This isattributable to the physical properties of an amp's constituent
42 Serial FX Loop Send43 Serial FX Loop Return44 Poweramp Output, 4 Ohms Parallel45 Poweramp Output, 8 Ohms Parallel46 Poweramp Output, 16 OhmsIMPORTA
2. An external 8-ohm cabinet and the internal speaker (1x12", 8 ohms) connectedto the 4-ohm jacks. When you unplug the cable for the external cab
Handling and Care:* Keep the amp safe from hard knocks and shocks. Tubes are fragile and tendto suffer when exposed to mechanical stress!* Let the a
TubeAmpTechnologyTubeAmpTechnology
Troubleshooting* Some features that may be controlled remotely using a Z-9 or Z-4 footswitchfail to respond when you change settings:* The amp fails
-> You may be looking at a faulty tube or another defect. In this case,be sure to take the preamp to an authorized, professional service center.-&g
Technical DataOutput power:Input sensitivity levelsInput:Output levelsPower consumption:Fuses:Important:Tubes:Logic control system:System interface:Co
Tube Map:Tube replacement report:1. Replaced on: _ _ _ _ _ _ _ 20 _ _ _ Replaced by: _ _ _ _ _ _ _ _ _ _ _ _ _ _Replaced tubes: _ _ _ _ _ _ _ _ _ _
ON/OFFON/OFFRAmpTubeFOOTPEDALZ-4Your Options for controlling the ENGL Raider 100 amp remotely:#1 ENGL Z-9 Custom Footswitch: This specialized footboa
Noting Settings:Sound title: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _comment: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Configuration table for assigning the Raider 100's sound-shaping andspecial functions to the Z-9 Custom Footswitch's and :Functions 1 2Butto
page: >6< <---------------------------------------- 7 ----------------------------------------> <-------------------- 8 ----
TubeAmpTechnologyTubeAmpTechnology Gerätebau GmbHGermanyInternet: http://www.engl-amps.comText, design, graphics, photography and layout by Hor
Table of ContentspageIntroductionFeatures and Functionality at a GlanceContentsFront Panel Features:Rear Panel Features:TroubleshootingTechnical Data,
Congratulations, ENGL Amp user! ENGL RaiderThe is one mean machine of a tube-driven guitar amplifier, engineered to inspire you and enthuse your audie
Your ENGL Raider 100 Amp puts at your disposal:Features and Functionality at a Glance1. a logical control feature array, utmost and;2. and : You canco
-> The optional Z-9 Custom Footswitch. It lets you select combinations of channelsand the two gain stages directly and control two sound-shaping fe
2 Bright3 Gain 14 Bass5 Middle6 TrebleChannel 1. This knob determines input sensitivity when Channel 1is active; use it to dial in the desired amount
you set all tone controls to or slightly higher than the center or 12 o'clock position. Forhigher-gain Crunch sounds, your best bet is to turn th
11Presence12DepthPunch13PowerTubeMonitorV114PowerTubeMonitorV215PowerTubeMonitorV316PowerTubeMonitorV4AnimportantnoteonthePowerTubeMonitor(P.T.M.)syst
Commentaires sur ces manuels